Replacing uPVC Window Handles
The replacement of window handles made of upvc is a fairly straightforward job. It is essential to ensure that the replacement handle fits into the spindle cutout in the window mechanism.
If the steps below are followed properly the cockspur handle will fit most windows. The step height of the handle is important.
What to Do You Look For?
A lot of windows in the UK come with uPVC handles and, over time, they may begin to show signs of wear and wear and tear. If this occurs, the handle can become loose or difficult to operate, making it necessary to replace it. This is a fairly easy task that can be accomplished by anyone who is comfortable using basic hand tools.
The first step is to make sure that the handle is securely attached to the frame of the window in its open position. Next, locate the screws or pins which hold the handle in place. They are usually on the inside of the handle. They can be removed with a screwdriver and pliers.
When the handle has become loose It is best to gently pull it away from its hinges. Then, you'll need to locate a replacement handle of the same size and style. This can be done on the internet or in a local DIY store, and the process should only take about five minutes with the help of a screwdriver.
One important factor to consider when replacing a uPVC window handle is the step height. This is the distance from the bottom of the handle until it rests on the frame of the window. This is typically a standard measurement, and it is important to examine the step height of your existing handle prior to ordering an entirely new one.
There are various sizes depending on the type of handle. Inline handles are offered for uPVC windows that have centers of 31mm for lugs, while cockspur handles have lug centres of 43 millimetres. Tilt-and turn handles are typically found on uPVC Windows. They have a special design that lets the window be slid down to let in air, and then turned to fully open the window.
The most common cause of breakage in uPVC handles is that they crack internally instead of breaking off from the base section. This makes it difficult to open. It is crucial to ensure that any replacement handle has the same spindle as the original one.
Remove the old handle
If your window handles are damaged or not properly installed, they could cause double-glazed windows to close and open incorrectly. They may even get stuck. There are a variety of reasons for this like general wear and tear, or corrosion of the handle. In these situations it is crucial to find replacement window handles made of upvc as soon as you can to avoid further damage and loss of function.
When replacing upvc windows handles it is recommended to remove the handles that were previously installed from the window. Start by removing the screw covered with the handle when it is in a closed position. Once you have removed that screw, you are able to remove the handle. It is recommended to use an electric screwdriver for this, as it makes the task easier and quicker.
It is also important to note that the screws on the handle could be hidden behind plastic caps, so it is recommended to take a Stanley knife to the screws and remove them. Once the old handle is removed, you must examine the square cut on the handle's base to ensure that the new window lock handles will work with it. It is important to measure the length of the spindle on the old handle and compare it to the size of the window mechanism spindle cutout.
There are three types of Upvc handles: Espag handles with a central screw that can be turned right or left and Cranked handles that have two screws and Spade handles, which have arms that are flat and can be used on either side of the windows made of upvc. It is simple to replace the handle once you've located one that is suitable. Just screw it into place, and make sure the spindle is inserted correctly in the lock mechanism. After that, it should be tightened to the window frame and your replacement window handles made of upvc should be secure.
Take a measurement of the Spindle
If you're looking to replace a handle made of upvc that has collapsed, it's likely the spindle that holds it in place is damaged or loose. In some cases it is possible to tighten the spindle by using pin or screw. In some instances it might be necessary to replace the handle. There are several kinds of window handles made of upvc. There are three types of handles: inline espagnolette tilt-and-turn, and cockspur. Each kind has a distinct procedure for installing and removing the handle.
It is essential to measure the current handle before buying the replacement. This will help ensure that the new handle is of the correct size and will fit correctly within the window. All handles are sized in accordance with industry standards, making it easy to determine the right size.
To determine upvc replacement door handles of your handle, first remove it from the window by turning it to the open position. You should be able to determine the size of the pin or screw that secures the handle. Then, use a tape measure or ruler to determine the length of the spindle. Once you have determined the length of the spindle, you can purchase a new spindle that is exactly the same size.
When you are looking to replace a handle window handle, it is crucial to consider the step height of the window handle made of upvc. The step height is the distance from the bottom of the handle to the point at which it is placed on the frame. Typically, this will be about 21mm for uPVC windows and 9mm for aluminum. To ensure that the new handle is suitable the gap, drop something into the gap to check how far it extends before meeting an obstruction.
Cockspur handles typically have different backset heights depending on the style of window they're installed in. Inline Espag handle heights are 43mm from centre to centre (two fixing points). Cockspur handles however, have different backset heights dependent on the style of the window they're in. This is because they have spurs that extend from the handle and locks over a cockspur wedge striker plate.
Install the new handle
When you've chosen a new handle, make sure you align it with the screw holes on the door and fix it using the screws supplied. Install the latch lever in similar fashion to the handle that you are replacing if you are also replacing the door handle. After that, attach the door trim again to hide the screws for mounting.
Tips: To take the metal head from the wooden wedge, hold the handle so its wider end is resting on the floor and use an hammer to tap the thin end of the handle. Be careful not to scratch the handle or spindle.